cpu_map.h

Go to the documentation of this file.

/*
  cpu_map.h - CPU and pin mapping configuration file
  Part of Grbl
 
  Copyright (c) 2012-2016 Sungeun K. Jeon for Gnea Research LLC
 
  Grbl is free software: you can redistribute it and/or modify
  it under the terms of the GNU General Public License as published by
  the Free Software Foundation, either version 3 of the License, or
  (at your option) any later version.
 
  Grbl is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  GNU General Public License for more details.
 
  You should have received a copy of the GNU General Public License
  along with Grbl.  If not, see <http://www.gnu.org/licenses/>.
*/
 
/* The cpu_map.h files serve as a central pin mapping selection file for different
   processor types or alternative pin layouts. This version of Grbl officially supports
   only the Arduino Mega328p. */
 
 
#ifndef cpu_map_h
#define cpu_map_h
 
 
#ifdef CPU_MAP_ATMEGA328P // (Arduino Uno) Officially supported by Grbl.
 
  // Define serial port pins and interrupt vectors.
  #define SERIAL_RX     USART_RX_vect
  #define SERIAL_UDRE   USART_UDRE_vect
 
  // Define step pulse output pins. NOTE: All step bit pins must be on the same port.
  #define STEP_DDR        DDRD
  #define STEP_PORT       PORTD
  #define X_STEP_BIT      2  // Uno Digital Pin 2
  #define Y_STEP_BIT      3  // Uno Digital Pin 3
  #define Z_STEP_BIT      4  // Uno Digital Pin 4
  #define STEP_MASK       ((1<<X_STEP_BIT)|(1<<Y_STEP_BIT)|(1<<Z_STEP_BIT)) // All step bits
 
  // Define step direction output pins. NOTE: All direction pins must be on the same port.
  #define DIRECTION_DDR     DDRD
  #define DIRECTION_PORT    PORTD
  #define X_DIRECTION_BIT   5  // Uno Digital Pin 5
  #define Y_DIRECTION_BIT   6  // Uno Digital Pin 6
  #define Z_DIRECTION_BIT   7  // Uno Digital Pin 7
  #define DIRECTION_MASK    ((1<<X_DIRECTION_BIT)|(1<<Y_DIRECTION_BIT)|(1<<Z_DIRECTION_BIT)) // All direction bits
 
  // Define stepper driver enable/disable output pin.
  #define STEPPERS_DISABLE_DDR    DDRB
  #define STEPPERS_DISABLE_PORT   PORTB
  #define STEPPERS_DISABLE_BIT    0  // Uno Digital Pin 8
  #define STEPPERS_DISABLE_MASK   (1<<STEPPERS_DISABLE_BIT)
 
  // Define homing/hard limit switch input pins and limit interrupt vectors.
  // NOTE: All limit bit pins must be on the same port, but not on a port with other input pins (CONTROL).
  #define LIMIT_DDR        DDRB
  #define LIMIT_PIN        PINB
  #define LIMIT_PORT       PORTB
  #define X_LIMIT_BIT      1  // Uno Digital Pin 9
  #define Y_LIMIT_BIT      2  // Uno Digital Pin 10
  #ifdef VARIABLE_SPINDLE // Z Limit pin and spindle enabled swapped to access hardware PWM on Pin 11.
    #define Z_LIMIT_BIT    4 // Uno Digital Pin 12
  #else
    #define Z_LIMIT_BIT    3  // Uno Digital Pin 11
  #endif
  #if !defined(ENABLE_DUAL_AXIS)
    #define LIMIT_MASK     ((1<<X_LIMIT_BIT)|(1<<Y_LIMIT_BIT)|(1<<Z_LIMIT_BIT)) // All limit bits
  #endif
  #define LIMIT_INT        PCIE0  // Pin change interrupt enable pin
  #define LIMIT_INT_vect   PCINT0_vect
  #define LIMIT_PCMSK      PCMSK0 // Pin change interrupt register
 
  // Define user-control controls (cycle start, reset, feed hold) input pins.
  // NOTE: All CONTROLs pins must be on the same port and not on a port with other input pins (limits).
  #define CONTROL_DDR       DDRC
  #define CONTROL_PIN       PINC
  #define CONTROL_PORT      PORTC
  #define CONTROL_RESET_BIT         0  // Uno Analog Pin 0
  #define CONTROL_FEED_HOLD_BIT     1  // Uno Analog Pin 1
  #define CONTROL_CYCLE_START_BIT   2  // Uno Analog Pin 2
  #define CONTROL_SAFETY_DOOR_BIT   1  // Uno Analog Pin 1 NOTE: Safety door is shared with feed hold. Enabled by config define.
  #define CONTROL_INT       PCIE1  // Pin change interrupt enable pin
  #define CONTROL_INT_vect  PCINT1_vect
  #define CONTROL_PCMSK     PCMSK1 // Pin change interrupt register
  #define CONTROL_MASK      ((1<<CONTROL_RESET_BIT)|(1<<CONTROL_FEED_HOLD_BIT)|(1<<CONTROL_CYCLE_START_BIT)|(1<<CONTROL_SAFETY_DOOR_BIT))
  #define CONTROL_INVERT_MASK   CONTROL_MASK // May be re-defined to only invert certain control pins.
 
  // Define probe switch input pin.
  #define PROBE_DDR       DDRC
  #define PROBE_PIN       PINC
  #define PROBE_PORT      PORTC
  #define PROBE_BIT       5  // Uno Analog Pin 5
  #define PROBE_MASK      (1<<PROBE_BIT)
 
  #if !defined(ENABLE_DUAL_AXIS)
 
    // Define flood and mist coolant enable output pins.
    #define COOLANT_FLOOD_DDR   DDRC
    #define COOLANT_FLOOD_PORT  PORTC
    #define COOLANT_FLOOD_BIT   3  // Uno Analog Pin 3
    #define COOLANT_MIST_DDR   DDRC
    #define COOLANT_MIST_PORT  PORTC
    #define COOLANT_MIST_BIT   4  // Uno Analog Pin 4
 
    // Define spindle enable and spindle direction output pins.
    #define SPINDLE_ENABLE_DDR    DDRB
    #define SPINDLE_ENABLE_PORT   PORTB
    // Z Limit pin and spindle PWM/enable pin swapped to access hardware PWM on Pin 11.
    #ifdef VARIABLE_SPINDLE
      #ifdef USE_SPINDLE_DIR_AS_ENABLE_PIN
        // If enabled, spindle direction pin now used as spindle enable, while PWM remains on D11.
        #define SPINDLE_ENABLE_BIT    5  // Uno Digital Pin 13 (NOTE: D13 can't be pulled-high input due to LED.)
      #else
        #define SPINDLE_ENABLE_BIT    3  // Uno Digital Pin 11
      #endif
    #else
      #define SPINDLE_ENABLE_BIT    4  // Uno Digital Pin 12
    #endif
    #ifndef USE_SPINDLE_DIR_AS_ENABLE_PIN
      #define SPINDLE_DIRECTION_DDR   DDRB
      #define SPINDLE_DIRECTION_PORT  PORTB
      #define SPINDLE_DIRECTION_BIT   5  // Uno Digital Pin 13 (NOTE: D13 can't be pulled-high input due to LED.)
    #endif
 
    // Variable spindle configuration below. Do not change unless you know what you are doing.
    // NOTE: Only used when variable spindle is enabled.
    #define SPINDLE_PWM_MAX_VALUE     255 // Don't change. 328p fast PWM mode fixes top value as 255.
    #ifndef SPINDLE_PWM_MIN_VALUE
      #define SPINDLE_PWM_MIN_VALUE   1   // Must be greater than zero.
    #endif
    #define SPINDLE_PWM_OFF_VALUE     0
    #define SPINDLE_PWM_RANGE         (SPINDLE_PWM_MAX_VALUE-SPINDLE_PWM_MIN_VALUE)
    #define SPINDLE_TCCRA_REGISTER    TCCR2A
    #define SPINDLE_TCCRB_REGISTER    TCCR2B
    #define SPINDLE_OCR_REGISTER      OCR2A
    #define SPINDLE_COMB_BIT          COM2A1
 
    // Prescaled, 8-bit Fast PWM mode.
    #define SPINDLE_TCCRA_INIT_MASK   ((1<<WGM20) | (1<<WGM21))  // Configures fast PWM mode.
    // #define SPINDLE_TCCRB_INIT_MASK   (1<<CS20)               // Disable prescaler -> 62.5kHz
    // #define SPINDLE_TCCRB_INIT_MASK   (1<<CS21)               // 1/8 prescaler -> 7.8kHz (Used in v0.9)
    // #define SPINDLE_TCCRB_INIT_MASK   ((1<<CS21) | (1<<CS20)) // 1/32 prescaler -> 1.96kHz
    #define SPINDLE_TCCRB_INIT_MASK      (1<<CS22)               // 1/64 prescaler -> 0.98kHz (J-tech laser)
 
    // NOTE: On the 328p, these must be the same as the SPINDLE_ENABLE settings.
    #define SPINDLE_PWM_DDR   DDRB
    #define SPINDLE_PWM_PORT  PORTB
    #define SPINDLE_PWM_BIT   3    // Uno Digital Pin 11
  
  #else
 
    // Dual axis feature requires an independent step pulse pin to operate. The independent direction pin is not 
    // absolutely necessary but facilitates easy direction inverting with a Grbl $$ setting. These pins replace 
    // the spindle direction and optional coolant mist pins.
 
    #ifdef DUAL_AXIS_CONFIG_PROTONEER_V3_51
      // NOTE: Step pulse and direction pins may be on any port and output pin.
      #define STEP_DDR_DUAL       DDRC
      #define STEP_PORT_DUAL      PORTC
      #define DUAL_STEP_BIT       4  // Uno Analog Pin 4
      #define STEP_MASK_DUAL      ((1<<DUAL_STEP_BIT))
      #define DIRECTION_DDR_DUAL  DDRC
      #define DIRECTION_PORT_DUAL PORTC
      #define DUAL_DIRECTION_BIT  3  // Uno Analog Pin 3
      #define DIRECTION_MASK_DUAL ((1<<DUAL_DIRECTION_BIT))
 
      // NOTE: Dual axis limit is shared with the z-axis limit pin by default. Pin used must be on the same port
      // as other limit pins.
      #define DUAL_LIMIT_BIT    Z_LIMIT_BIT
      #define LIMIT_MASK        ((1<<X_LIMIT_BIT)|(1<<Y_LIMIT_BIT)|(1<<Z_LIMIT_BIT)|(1<<DUAL_LIMIT_BIT))
 
      // Define coolant enable output pins.
      // NOTE: Coolant flood moved from A3 to A4. Coolant mist not supported with dual axis feature on Arduino Uno.
      #define COOLANT_FLOOD_DDR   DDRB
      #define COOLANT_FLOOD_PORT  PORTB
      #define COOLANT_FLOOD_BIT   5  // Uno Digital Pin 13
 
      // Define spindle enable output pin.
      // NOTE: Spindle enable moved from D12 to A3 (old coolant flood enable pin). Spindle direction pin is removed.
      #define SPINDLE_ENABLE_DDR    DDRB
      #define SPINDLE_ENABLE_PORT   PORTB
      #ifdef VARIABLE_SPINDLE
        // NOTE: USE_SPINDLE_DIR_AS_ENABLE_PIN not supported with dual axis feature.
        #define SPINDLE_ENABLE_BIT    3  // Uno Digital Pin 11
      #else
        #define SPINDLE_ENABLE_BIT    4  // Uno Digital Pin 12
      #endif
 
      // Variable spindle configuration below. Do not change unless you know what you are doing.
      // NOTE: Only used when variable spindle is enabled.
      #define SPINDLE_PWM_MAX_VALUE     255 // Don't change. 328p fast PWM mode fixes top value as 255.
      #ifndef SPINDLE_PWM_MIN_VALUE
        #define SPINDLE_PWM_MIN_VALUE   1   // Must be greater than zero.
      #endif
      #define SPINDLE_PWM_OFF_VALUE     0
      #define SPINDLE_PWM_RANGE         (SPINDLE_PWM_MAX_VALUE-SPINDLE_PWM_MIN_VALUE)
      #define SPINDLE_TCCRA_REGISTER    TCCR2A
      #define SPINDLE_TCCRB_REGISTER    TCCR2B
      #define SPINDLE_OCR_REGISTER      OCR2A
      #define SPINDLE_COMB_BIT          COM2A1
 
      // Prescaled, 8-bit Fast PWM mode.
      #define SPINDLE_TCCRA_INIT_MASK   ((1<<WGM20) | (1<<WGM21))  // Configures fast PWM mode.
      // #define SPINDLE_TCCRB_INIT_MASK   (1<<CS20)               // Disable prescaler -> 62.5kHz
      // #define SPINDLE_TCCRB_INIT_MASK   (1<<CS21)               // 1/8 prescaler -> 7.8kHz (Used in v0.9)
      // #define SPINDLE_TCCRB_INIT_MASK   ((1<<CS21) | (1<<CS20)) // 1/32 prescaler -> 1.96kHz
      #define SPINDLE_TCCRB_INIT_MASK      (1<<CS22)               // 1/64 prescaler -> 0.98kHz (J-tech laser)
 
      // NOTE: On the 328p, these must be the same as the SPINDLE_ENABLE settings.
      #define SPINDLE_PWM_DDR   DDRB
      #define SPINDLE_PWM_PORT  PORTB
      #define SPINDLE_PWM_BIT   3    // Uno Digital Pin 11
    #endif
 
    // NOTE: Variable spindle not supported with this shield.
    #ifdef DUAL_AXIS_CONFIG_CNC_SHIELD_CLONE
      // NOTE: Step pulse and direction pins may be on any port and output pin.
      #define STEP_DDR_DUAL       DDRB
      #define STEP_PORT_DUAL      PORTB
      #define DUAL_STEP_BIT       4  // Uno Digital Pin 12
      #define STEP_MASK_DUAL      ((1<<DUAL_STEP_BIT))
      #define DIRECTION_DDR_DUAL  DDRB
      #define DIRECTION_PORT_DUAL PORTB
      #define DUAL_DIRECTION_BIT  5  // Uno Digital Pin 13
      #define DIRECTION_MASK_DUAL ((1<<DUAL_DIRECTION_BIT))
 
      // NOTE: Dual axis limit is shared with the z-axis limit pin by default.
      #define DUAL_LIMIT_BIT    Z_LIMIT_BIT
      #define LIMIT_MASK        ((1<<X_LIMIT_BIT)|(1<<Y_LIMIT_BIT)|(1<<Z_LIMIT_BIT)|(1<<DUAL_LIMIT_BIT))
 
      // Define coolant enable output pins.
      // NOTE: Coolant flood moved from A3 to A4. Coolant mist not supported with dual axis feature on Arduino Uno.
      #define COOLANT_FLOOD_DDR   DDRC
      #define COOLANT_FLOOD_PORT  PORTC
      #define COOLANT_FLOOD_BIT   4  // Uno Analog Pin 4
 
      // Define spindle enable output pin.
      // NOTE: Spindle enable moved from D12 to A3 (old coolant flood enable pin). Spindle direction pin is removed.
      #define SPINDLE_ENABLE_DDR    DDRC
      #define SPINDLE_ENABLE_PORT   PORTC
      #define SPINDLE_ENABLE_BIT    3  // Uno Analog Pin 3
    #endif
 
  #endif
 
#endif
 
/*
#ifdef CPU_MAP_CUSTOM_PROC
  // For a custom pin map or different processor, copy and edit one of the available cpu
  // map files and modify it to your needs. Make sure the defined name is also changed in
  // the config.h file.
#endif
*/
 
#endif